Hotline: 090 343 3214

Scissor Lift Family

Key Features At A Glance
Extra-Wide Runways

  24" (RX10 and RX12) or 26" (RX16) runways accept wide vehicles
 
Integrated Air Line Kit

  Convenient air source for tools at front and rear
 
Two Movable Work Steps

  12 secure positions

  Lightweight design

Louvered Ramps

  Prevent wheel spin in wet conditions

  More effective than diamond tread or abrasive strips
 
Control Panel

  Complete operation from the console

  Optional PowerSlide, Inflation Station and FIA control
 
Inflation Station (optional)

  Automatically fills or bleeds each tire

  No hanging air lines

Pins and Bearings

  Chromed pins and teflon bearings for long life
 
Safety Locks

  Precision-fit teeth lock runways at 16 level height positions
 
Velocity Safety Fuses

  Instantaneous shutdown in event of hydraulic failure

Sensor Feedback System

  Sensors keep runway level

  Safely stops if obstructed
 
Two Swing Air Jacks

  6,000-lb.capacity

  Technicians' favorite
 
Stainless Steel Turnplates
Stainless Steel Turnplates

  Corrosion resistant

  Maintains free movement

Fast Descent Speed

The hydraulic system speeds lowering times by 50%.

The system automatically slows the descent in the last several inches to ensure a soft landing.

The fast descent feature is standard with Inflation Station (IS) models.

 
Swing Air Jacks

Hunter Swing Air Jacks add capabilities for lifting vehicles off the runways during alignment procedures and other multi-service operations.

Each Swing Air Jack combines low drive-on height with high lifting capacity needed to handle a wide range of vehicles.

133-69-1 – 6,000-lb. Capacity Swing Air Jack

133-83-1 – 9,000-lb. Capacity Swing Air Jack


Flush-Mount Installation

Lifts may be flush-mounted in a shallow recess. No more worries about lowered vehicles or expensive spoilers! This very tidy installation is ideal for “showcase” shops.

No additional charge for flush-mount option. Contact your Hunter Sales Representative for details.

Add F to any RX model number.

 
AlignLights System

Hunter’s integrated AlignLights lighting system provides an efficient light source underneath the vehicle.

AlignLights automatically turns on when the lift is raised and turns off when the lift is lowered to the floor.

AlignLights is an ALI-listed accessory.

20-2173-1 – AlignLights system


Power-Up System
power up system

Hunter’s dual-capacity lifting system offers the ground-clearance advantages of a standard- capacity lift to handle most vehicles.

To service heavy vehicles, the exclusive Power-Up feature boosts lifting capacity to a massive 16,000 lbs.

Only Hunter’s RX16 combines the versatility of a low-profile design with tremendous power to provide the widest range of service with one lift.

   

Hunter Offers Two Fully Integrated Options to Enhance Productivity
fully integrated alignment


FIA allows WinAlign® aligners to control lift features for ultimate productivity. Two patented designs offer greater flexibility and timesaving capabilities.

 
fully integrated alignment


** Requires FIA equipped aligner with WinAlign 10.x software or greater.

Max. vehicle weight:

Max. lifting height:
16,000-lb. mode
Standard-capacity mode
Flush-mount version

Alignment height:

Lifting speed:
Lowering speed:

 

16,000 lbs. (7257 kg)


68” (1727 mm)
76” (1930 mm)
72” (1829 mm)

All lock positions

60 seconds
25 seconds

 

Tread width:
Min inside
Max. outside

Max. wheelbase:
General service
Two-wheel alignment
Four-wheel alignment 

Min. four-wheel alignment:
 

 


40" (1016 mm)
92" (2337 mm) 


187" (4749 mm)
182" (4623 mm)
158" (4013 mm)

68" (1727 mm)


Models

RX16JT: RX16 with (2) 9,000-lb. Swing Air Jacks and stainless steel turnplates

RX16JFT: Flush-mount RX16 with (2) 9,000-lb Swing Air Jacks and stainless steel turnplates

RX16T-PS: RX16 with (2) 9,000-lb. Swing Air Jacks, PowerSlide slipplates and turnplates, and FIA

RX16FT-PS: Flush-mount RX16 with (2) 9,000-lb. Swing Air Jacks, PowerSlide slipplates and turnplates, and FIA

RX16T-IS: RX16 with (2) 9,000-lb. Swing Air Jacks, PowerSlide slipplates and turnplates, Inflation Station, and FIA

RX16FT-IS: Flush-mount RX16 with (2) 9,000-lb. Swing Air Jacks, PowerSlide slipplates and turnplates, Inflation Station, and FIA

Standard Equipment

Stainless steel turnplates (PowerSlide turnplates on PS and IS models) 
Flush-mounted, full-floating slipplates (PowerSlide slipplates on PS and IS models) 
Two movable work steps (not included with flush-mount installations) 
Louvered ramps with built-in wheel stops 
Front wheel stops 
Two wheel chocks 
Built-in, full-length jack rails 
Built-in air line kit

 
rx-12 plan view
validated by etl - ali certified
The Hunter RX16 Series Scissor Lift has been certified under the program conducted by Automotive Lift Institute (ALI) and ETL Testing Laboratories to comply with Safety Standard ANSI/ ALI, ALCTV and Electrical Standard ANSI/UL 201.

Lift Rack Spec Sheets
 
           

Approach Ramp Extensions
Extensions lessen the ramp incline for high-floor-slope installs and ease service for specialty vehicles.
  Conventional Sensor Extension
Provides additional space at the front of runways. Required when using conventional sensors with toe arms.
  Drive-Thru Kit
For surface-mount, drive-thru application. Use standard kit for camera sensors and extended kit for conventional sensors.
 
Approach Ramp Extensions

147-104-1 – Adds 13” (2 required). 

147-113-1 – Adds 18” (2 required).
 
Conventional Sensor Extension

20-2497-1 – Adds approximately 12” in length.
 
Drive-Thru Kit

20-2498-1 – Standard kit for camera sensors. Adds 53” in length. 

20-2501-1 – Extended kit for conventional sensors. Adds 61” in length.